MAX320EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX320 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 8V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 200μA |
| Max Supply Current | 125μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switch-off Time-Max | 100ns |
| Voltage - Supply, Dual (V±) | ±2.7V~8V |
| Height Seated (Max) | 1.11mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX320EUA+ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 8 terminations. The electronic part delivers high-quality output through its 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 8 series of products. Multiplexers built on a SPST - NO switching circuit are built. It consists of 2 circuits. Use MAX320 to search for variants of the digital switches. There is 35Ohm internal resistance in this digital multiplexer. You can find the functions of the 8 pins in the datasheets. It is generally not recommended to supply a voltage higher than 8V to the switch device in normal circumstances. Dual supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 2.7V. For this digital switch to work, 1μA current would suffice. Put voltage above 125μA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. In the case of dual power supplies, you should connect at least 2.7V.
MAX320EUA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX320EUA+ Applications
There are a lot of Maxim Integrated MAX320EUA+ Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- SONET/SDH ADM
- Mechanical reed relay replacement
- Precision test equipment
- CSU
- Frame Relay Equipment
- Medical
- Channelized and Unchannelized DS3 applications
- Cellular phones
- Microprocessor Controlled Analog Systems
