MAX321CPA+

150ns, 100ns SPST - NC 35Ohm Analog Switches MAX321 8 Pins 100pA 5V 8-DIP (0.300, 7.62mm)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX321CPA+
Package: 8-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 655
Description: 150ns, 100ns SPST - NC 35Ohm Analog Switches MAX321 8 Pins 100pA 5V 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	8-DIP (0.300, 7.62mm)
Number of Pins	8
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	1995
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	35Ohm
Max Power Dissipation	330mW
Technology	CMOS
Number of Functions	2
Supply Voltage	5V
Base Part Number	MAX321
Pin Count	8
Operating Supply Voltage	8V
Number of Channels	1
Number of Circuits	2
Operating Supply Current	1μA
Nominal Supply Current	80μA
Max Supply Current	80μA
Throw Configuration	SPST
Turn On Delay Time	150 ns
Supply Type	Dual
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.7V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	150ns, 100ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switch-on Time-Max	175ns
Voltage - Supply, Dual (V±)	±2.7V~8V
Length	9.375mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX321CPA+ Overview

Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. It is mounted in the position Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around 0°C~70°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. These analog multiplexers are built based on SPST - NC switching circuits. A 2 circuit is present in this switch device. Try searching with MAX321 if you're looking for variants. It has an internal resistance of 35Ohm. Please refer to the datasheets for 8 pins functions. Analogue multiplexer with a Dual supply type that is cost-effective. For this multiplexer to operate, 1μA current would be sufficient. The analogue multiplexer may be damaged if voltage is greater than 80μA. For this switch, a dual supply voltage is feasible, but it must not exceed 8VIn the case of dual power supplies, you should connect at least 2.7V. It can operate from 8V operating voltages.