MAX3223EAP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 453.59237mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 3V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3223 |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Interface | RS-232 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 300μA |
| Propagation Delay | 300 ns |
| Logic Function | Receiver, Transceiver |
| Data Rate | 120Kbps |
| Output Characteristics | 3-STATE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Driver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 300mV |
| Number of Transceivers | 1 |
| ESD Protection | No |
| Simplex/Duplex | Full Duplex |
| Number of Receivers | 2 |
| Height | 1.78mm |
| Length | 7.33mm |
| Width | 5.38mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3223EAP+ Overview
LED drivers benefit from this IC's enhanced 20-SSOP (0.209, 5.30mm Width) package.In this package, the receiver is mounted in the Tube format.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.PCBs or development boards with Surface Mount-types can accommodate this wide receiver.This differential driver requires a 3V~5.5V power supply.It is possible to have up to 2/2 receivers/drivers in use simultaneously with this electronic part.IC receiver has been designed primarily for applications operating at -40°C~85°C.An operating voltage range of 3.3V is suitable for this line driver ic.There are 20 terminations in this wide receiver so that signals can be driven from the data and received.It is packaged with 20 pinouts that are market standard for this particular transceiver.Since the part number MAX3223 represents the product type, temperature, package, etc., you can try searching with that number to find more variants.An enhanced power dissipation driver IC with 20 pins.Through optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size is reduced dramatically.Using this ic receiver, you were able to achieve a resolution of 2 bits.There is a 5V input voltage supply that can be used to operate this transceiver module.A subcategory named Line Driver or Receivers can be used to group this rf transceiver module.Transceivers implemented by this IC total 1 in total.In module isolated transceiver are 2 receivers.An input voltage of 1mA is recommended for this integrating circuit to be able to drive LEDs.
MAX3223EAP+ Features
Tube package
20 pin count
20 pins
MAX3223EAP+ Applications
There are a lot of Maxim Integrated MAX3223EAP+ Drivers/Receivers/Transceivers applications.
- TV signal transmission
- Transmission stations
- Wireless multimedia center in smart home
- Metro access rings
- Point-to-point networking
- Bar, KTV wireless entertainment
- Changeing the frequency from IF to RF
- transmission relay
- Satellite ground stations
- Home theater wiring-free
