MAX322CPA+
| Parameters | |
|---|---|
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Voltage - Supply, Dual (V±) | ±2.7V~8V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX322 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 8V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 80μA |
| Max Supply Current | 125μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 2.7V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
MAX322CPA+ Overview
Shipping overseas is convenient with the electronic component packed in 8-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. Multiplexers like this are mounted in the Through Hole position. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. In total, 8 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. This multiplexer is composed of 2 circuits. Try searching with MAX322 to find analog multiplexer variants. In this multiplexer, the internal resistance is 35Ohm. For details about the functions of 8 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 8V. A cost-effective Dual supply type analogue multiplexer. It is recommended to use 2.7V as the lowest voltage for the electrical part. This multiplexer would work with 1μA current. Put voltage above 125μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 8V. In the case of dual power supplies, you should connect at least 2.7V.
MAX322CPA+ Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX322CPA+ Applications
There are a lot of Maxim Integrated MAX322CPA+ Analog Switches & Multiplexers ICs applications.
- Medical systems
- USB 1.1 signal switching circuits
- Industrial and process control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Industrial
- Relay Replacement
- Sample hold systems
- HDTV
- DVD-R
- Precision instrumentation
