MAX3233EEWP+G36
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX3233 |
| Pin Count | 20 |
| Operating Supply Voltage | 3.3V |
| Interface | RS-232 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1μA |
| Propagation Delay | 250 ns |
| Data Rate | 250kbps |
| Differential Output | NO |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Number of Drivers | 2 |
| Number of Transceivers | 1 |
| ESD Protection | Yes |
| Simplex/Duplex | Full Duplex |
| Height | 2.65mm |
| Length | 13mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3233EEWP+G36 Overview
This driver chip is excellent for driving common LEDs due to its enhanced 20-SOIC (0.295, 7.50mm Width) package.There is a Tube package for this receiver.With its Transceiver can transceiver design, this part can be incorporated into a wide range of solutions.You can place this wide receiver to any Surface Mount-type PCB or development board.This differential driver uses 3V~3.6V for power supply.At any one time, this electronic part can have up to 2/2 eligible receivers/drivers.The operating temperature of this ic receiver is -40°C~85°C. It is primarily designed for applications with low temperatures.An output voltage range of 3.3V is sufficient to run this line driver ic efficiently.This integrated circuit has 20 terminations designed for driving and receiving signals from data.There are 20 pinouts available on this transceiver which are market standard.As the base part number MAX3233 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.This is a 20-pin driver IC with enhanced power dissipation control.As a result of optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size has been greatly reduced.There is usually a 2-bit resolution specified for this receiver when it is used.There is a 3.3V input voltage supply that can be used to operate this transceiver module.This rf transceiver module can be grouped into a subcategory named Line Driver or Receivers.Regarding the number of transceiver this module isolated transceiver implements, there are 1 transceivers overall.The integrator circuit is embedded with 2 drivers.Input voltage is set to a value of 1mA, and this integrating circuit is capable of driving LEDs with that voltage.
MAX3233EEWP+G36 Features
Tube package
20 pin count
20 pins
MAX3233EEWP+G36 Applications
There are a lot of Maxim Integrated MAX3233EEWP+G36 Drivers/Receivers/Transceivers applications.
- Wireless communication
- Radio transmission
- interconnection between computers
- Low power, low voltage systems
- Notebook
- Pocket PC
- Metro access rings
- IPTV front end
- Bar, KTV wireless entertainment
- Sensor reporting
