Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1998 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
60Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
727mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX323 |
Pin Count |
8 |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Nominal Supply Current |
100pA |
Max Supply Current |
100pA |
Throw Configuration |
SPST |
Turn On Delay Time |
150 ns |
Supply Type |
Single |
Turn-Off Delay Time |
100 ns |
On-State Resistance (Max) |
60Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.8Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
800m Ω |
Crosstalk |
-85dB @ 1MHz |
Voltage - Supply, Single (V+) |
2.7V~16V |
Height Seated (Max) |
1.11mm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX323EUA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 8 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. Try searching for MAX323 variants of the analog switch ic. As far as internal resistance is concerned, it has 60Ohm. You can find the functions of the 8 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. The digital multiplexer has a low cost Single supply. 2.7V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 1μA. Analogue multiplexers require a 2.7V~16V voltage to drain from a single voltage supply. If put voltage greater than 100pA on the device, damage may be caused to the analogue multiplexer.
MAX323EUA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX323EUA+ Applications
There are a lot of Maxim Integrated MAX323EUA+ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Microprocessor controlled systems
- Isolation
- Automotive applications
- Avionics test equipment
- Private Branch Exchange (PBX)
- Data Acquisition Systems
- Optical Applications
- DSUs
- Avionics and Military Systems