MAX323EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX323 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Height Seated (Max) | 1.11mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX323EUA+T Overview
The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. The total number of terminations is 8. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. The electrical component body receives 8 pins. A SPST - NO switching circuit is used to build these analog multiplexers. A total of 2 circuits make up this switch device. Look for analog switch ic variants by searching with MAX323. The internal resistance of this digital multiplexer is 60Ohm. You can find the functions of the 8 pins in the datasheets. Multiplexers should not be powered above 16V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. A low voltage of 2.7V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~16V. The analogue multiplexer may be damaged if voltage is greater than 100pA.
MAX323EUA+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX323EUA+T Applications
There are a lot of Maxim Integrated MAX323EUA+T Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- Mechanical reed relay replacement
- Routers
- Multiplexers
- SONET
- Audio and video routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- 65 V DACs
- PDH Multiplexers
- CSU
