MAX324CPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX324 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switch-off Time-Max | 100ns |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX324CPA+ Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around 0°C~70°C TA. In total, there have been 8 terminations. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NC switching circuits. The multiplexer consists of 2 circuits. Search with MAX324 if you are looking for analog multiplexer variants. Analog switches have 60Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. Users should never supply a voltage higher than 16V to a switch device. Analog switch ics with Single supply type are cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. An operating current of 1μA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 2.7V~16V voltage. When the digital multiplexer is charged above 1μA, damage can occur.
MAX324CPA+ Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX324CPA+ Applications
There are a lot of Maxim Integrated MAX324CPA+ Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Digital cross connects (DSX-1)
- Fiber to the Home
- USB 1.1 signal switching circuits
- Cable PC
- DSUs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Systems
- Precision data acquisition
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
