MAX325CSA
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX325 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Drain to Source Resistance | 33Ohm |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX325CSA Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 2 channels. An 5V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 8 pins. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Try searching for MAX325 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 60Ohm. For details about the functions of 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 16V to a switch device. An effective Single supply digital multiplexer. A low voltage of 2.7V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. This analogue multiplexer requires a voltage of 2.7V~16V when it drains from a single voltage supply. Putting voltage greater than 100pA on the multiplexer may cause damage. It has a Drain to Source resistance of 33Ohm ohms.
MAX325CSA Features
2 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
Drain-to-Source resistance: 33Ohm
MAX325CSA Applications
There are a lot of Maxim Integrated MAX325CSA Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Cross Connects
- Relay replacements
- Sample hold systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- T1/E1 Terminals
- Precision test equipment
- Residential Gateways, Home Gateway/Router
- Isolation
- Ultrasound
