MAX325CUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX325 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX325CUA+T Overview
The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 8. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO/NC switching circuits. 2 circuits are used in this analogue multiplexer. Search with MAX325 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 60Ohm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 16V to the switch device in normal circumstances. An effective Single supply digital multiplexer. 2.7V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 1μA current would be sufficient. An analogue multiplexer drains from a single voltage supply at 2.7V~16V. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX325CUA+T Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX325CUA+T Applications
There are a lot of Maxim Integrated MAX325CUA+T Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Digital cross connects (DSX-1)
- Industrial and process control systems
- SONET
- Ultrasound
- Microprocessor controlled systems
- RGB switches
- Cellular phones
- Intelligent PBX
- Audio and video switching
