MAX325EUA+
| Parameters | |
|---|---|
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX325 |
| Output | SEPARATE OUTPUT |
| Power Supplies | 3.3/5V |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
MAX325EUA+ Overview
Due to its 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. Totally, there are 8 terminations. These analog multiplexers are built based on SPST - NO/NC switching circuits. A total of 2 circuits make up this switch device. Try searching for the analog switch ic with MAX325 if you are looking for variants. As far as internal resistance is concerned, it has 60Ohm. Please refer to the datasheets for 8 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2.7V. The switch device would be able to operate with 1μA current. This analogue multiplexer requires a voltage of 2.7V~16V when it drains from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX325EUA+ Features
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX325EUA+ Applications
There are a lot of Maxim Integrated MAX325EUA+ Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Precision test equipment
- ISDN NT1/TA
- New designs requiring multiplexer functions
- Fault Tolerant Systems
- Wireless Local Loop
- Battery-powered systems
- Data Acquisition Systems
- Public switching systems
- Precision data acquisition
