MAX326CEE+T
| Parameters | |
|---|---|
| Supply Voltage | 15V |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX326 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 90μA |
| Max Supply Current | 250μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.7pF 1.7pF |
| On-state Resistance Match-Nom | 75Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 175 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
MAX326CEE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SSOP (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around 0°C~70°C TA extended. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Circuits based on SPST - NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Try searching for MAX326 variants of the analog switch ic. In this multiplexer, the internal resistance is 3.5kOhm. Datasheets for 16 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 10V. When the digital multiplexer is charged above 250μA, damage can occur. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 4.5V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
MAX326CEE+T Features
1 Channels
Switch Circuit: SPST - NC
MAX326CEE+T Applications
There are a lot of Maxim Integrated MAX326CEE+T Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- Microprocessor Controlled Analog Systems
- Battery Powered Instruments
- Channelized and Unchannelized DS3 applications
- ISDN NT1/TA
- Precision instrumentation
- RGB switches
- Audio/video switches
- Digital Cross-Connects
- DSUs
