MAX326CSE+T
| Parameters | |
|---|---|
| JESD-30 Code | R-PDSO-G16 |
| Polarity | Non-Inverting |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 90μA |
| Max Supply Current | 90μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 1 μs |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.7pF 1.7pF |
| On-state Resistance Match-Nom | 75Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 175 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX326 |
| Pin Count | 16 |
MAX326CSE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. 16 pins are injected to the electronic part body. SPST - NC switching circuits are used in these analog switch ics. There are 4 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX326. A 3.5kOhm internal resistance characterizes this multiplexer. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. 10V is the lowest voltage the electrical component should receive. It may damage the digital multiplexer if the voltage is higher than 90μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. A dual power supply should have at least 4.5V voltage attached.
MAX326CSE+T Features
1 Channels
Switch Circuit: SPST - NC
MAX326CSE+T Applications
There are a lot of Maxim Integrated MAX326CSE+T Analog Switches & Multiplexers ICs applications.
- Central office
- HDTV
- MP3 players
- Video switching
- Signal routing between systems
- Sample-and-hold systems
- Digital Cross-Connects
- PBXs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- High reliability control systems
