Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1996 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
3.5kOhm |
Terminal Finish |
Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX326 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Nominal Supply Current |
90μA |
Max Supply Current |
250μA |
Throw Configuration |
SPST |
Turn On Delay Time |
1 μs |
Voltage - Supply, Single/Dual (±) |
10V~30V ±5V~18V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
500 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
3.5kOhm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
10pA |
Channel Capacitance (CS(off), CD(off)) |
1.7pF 1.7pF |
On-state Resistance Match-Nom |
75Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
1μs, 500ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
175 Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
1000ns |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX326ESE+ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NC switching circuit is used to build these analog multiplexers. 4 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX326. The internal resistance of this digital multiplexer is 3.5kOhm. You can find the functions of the 16 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 30V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 10V. When the digital multiplexer is charged above 250μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 18VWith dual power supplies, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
MAX326ESE+ Features
1 Channels
Switch Circuit: SPST - NC
MAX326ESE+ Applications
There are a lot of Maxim Integrated MAX326ESE+ Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Audio signal routing
- FTTH
- PDAs
- USB 1.1 signal switching circuits
- PCMCIA cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Multi-Line E1 Interface Cards
- Frame Relay Equipment
- Voice over IP/DSL – Integrated Access Devices, Smart