MAX328EPE+
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX328 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 4.5μA |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.8pF 8pF |
| On-state Resistance Match-Nom | 30Ohm |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 70 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
MAX328EPE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Through Hole. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. In total, there are 16 terminations. A electrical component with 8 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. A 1 circuit is present in this switch device. Using the MAX328 search parameter, you can discover variants of the switch. This digital multiplexer has 3.5kOhm internal resistance. Datasheets for functions of 16 pins are available. Multiplexers should not be powered above 30V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 10V. The switch device would be able to operate with 4.5μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 200μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. The voltage should be at least 5V if you are using dual power supplies. The electrical part can be operated at 28V voltage levels.
MAX328EPE+ Features
8 Channels
4.5μA Supply Current
MAX328EPE+ Applications
There are a lot of Maxim Integrated MAX328EPE+ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- SDH
- Audio and video routing
- Audio and video switching
- Medical systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- FTTH
- Central office
- RGB switches
- Microprocessor controlled systems
