MAX329CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX329 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 4.5μA |
| Throw Configuration | 4PST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.8pF 8pF |
| On-state Resistance Match-Nom | 30Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 70 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1500ns |
| Switch-off Time-Max | 1000ns |
| Signal Current-Max | 0.01A |
| Length | 19.175mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX329CPE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have a number of circuits 4:1. Increasing operating temperature to around 0°C~70°C TA. In total, there are 16 terminations. Due to its 2 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 16 pins. Multiplexers built on a SP4T switching circuit are built. MAX329 can be used to search for analog multiplexer variants. It has an internal resistance of 3.5kOhm. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 30V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 10V should be applied to the electronic component. The analogue multiplexer could operate on 4.5μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 18V. In the case of dual power supplies, you should connect at least 5V. There is a voltage range of 28V operating voltages for the electrical part.
MAX329CPE+ Features
2 Channels
Switch Circuit: SP4T
4.5μA Supply Current
MAX329CPE+ Applications
There are a lot of Maxim Integrated MAX329CPE+ Analog Switches & Multiplexers ICs applications.
- RGB switches
- Automotive applications
- Central office
- Microprocessor controlled systems
- PBX interfaces
- E1 Multiplexer
- USB 1.1 signal switching circuits
- Digital cross connects (DSX-1)
- High speed data transmission line cards
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
