Parameters |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.295, 7.50mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2011 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
3.5kOhm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
750mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX329 |
Pin Count |
16 |
Operating Supply Voltage |
28V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
4.5μA |
Throw Configuration |
4PST |
Propagation Delay |
1.5 μs |
Turn On Delay Time |
1.5 μs |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
10V~30V ±5V~18V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
1 μs |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
3.5kOhm |
Min Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
84 dB |
Current - Leakage (IS(off)) (Max) |
10pA |
Channel Capacitance (CS(off), CD(off)) |
1.8pF 8pF |
On-state Resistance Match-Nom |
30Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
1.5μs, 1μs |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
70 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
1500ns |
Switch-off Time-Max |
1000ns |
Signal Current-Max |
0.01A |
Height |
2.35mm |
Length |
10.5mm |
Width |
7.6mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
MAX329CWE+ Overview
The electrical component comes in 16-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. In total, 16 terminations have occurred. As a result of its 4 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SP4T switching circuits. The circuits in this analogue multiplexer number 2. Look for analog switch ic variants by searching with MAX329. This digital multiplexer has 3.5kOhm internal resistance. To find out what the 16 pins do, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 30V. Dual, Single supply type digital switch with a low cost. 10V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 4.5μA. Despite this switch device's dual supply capability, its voltage should not exceed 18V. If you are using a dual power supply, you should attach at least 5V. There is a voltage range of 28V operating voltages for the electrical part.
MAX329CWE+ Features
4 Channels
Switch Circuit: SP4T
4.5μA Supply Current
MAX329CWE+ Applications
There are a lot of Maxim Integrated MAX329CWE+ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- 65 V DACs
- Transmit
- Sample hold systems
- DSUs
- E1 Network Equipment
- Ultrasound
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- High-Voltage
- Multi-Line E1 Interface Cards