MAX329EPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX329 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 4.5μA |
| Throw Configuration | 4PST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.8pF 8pF |
| On-state Resistance Match-Nom | 30Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 70 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1500ns |
| Switch-off Time-Max | 1000ns |
| Signal Current-Max | 0.01A |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX329EPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 4:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. The electronic part delivers high-quality output through its 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. SP4T switching circuits are used in these analog switch ics. A 2 circuit is present in this switch device. Using the MAX329 search parameter, you can discover variants of the switch. Analog switches have 3.5kOhm internal resistance. The datasheets for the 16 pins explain the functions. Multiplexers should not be powered above 30V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 10V voltage fed to the electrical part below 10V. For this digital switch to work, 4.5μA current would suffice. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. If you are using a dual power supply, you should attach at least 5V. Operating voltages of 28V are compatible with the electrical part.
MAX329EPE+ Features
4 Channels
Switch Circuit: SP4T
4.5μA Supply Current
MAX329EPE+ Applications
There are a lot of Maxim Integrated MAX329EPE+ Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- CSU
- FTTH
- E1 Network Equipment
- Relay replacements
- DSUs
- Routers
- Communication systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channelized and Unchannelized DS3 applications
