MAX329EWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 750mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX329 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 4.5μA |
| Throw Configuration | 4PST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.8pF 8pF |
| On-state Resistance Match-Nom | 30Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 70 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1500ns |
| Switch-off Time-Max | 1000ns |
| Signal Current-Max | 0.01A |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX329EWE+ Overview
Due to its 16-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 4:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. The electrical component body receives 16 pins. A SP4T switching circuit is used to build these analog multiplexers. There are 2 circuits in this switch device. MAX329 can be used to search for analog multiplexer variants. This digital multiplexer has 3.5kOhm internal resistance. For functions related to 16 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 30V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10V. It would be sufficient to run this analogue multiplexer with 4.5μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. You should attach at least 5V voltage if you are using dual power supply. 28V operating voltages can be used with this electrical part.
MAX329EWE+ Features
4 Channels
Switch Circuit: SP4T
4.5μA Supply Current
MAX329EWE+ Applications
There are a lot of Maxim Integrated MAX329EWE+ Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Precision test equipment
- Multiplexers
- Sample hold systems
- Intelligent PBX
- Industrial
- Digital Cross-Connects
- RGB switches
- Avionics and Military Systems
- Battery-powered systems
