banner_page

MAX332CPE

1μs, 500ns SPST - NO 175Ohm Analog Switches BREAK-BEFORE-MAKE MAX332 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX332CPE
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 156
  • Description: 1μs, 500ns SPST - NO 175Ohm Analog Switches BREAK-BEFORE-MAKE MAX332 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2016
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 175Ohm
Terminal Finish Tin/Lead (Sn85Pb15)
Subcategory Multiplexer or Switches
Max Power Dissipation 470mW
Technology CMOS
Number of Functions 4
Supply Voltage 15V
Base Part Number MAX332
Output SEPARATE OUTPUT
Power Supplies +-15V
Number of Circuits 4
Max Supply Voltage 20V
Min Supply Voltage 4.5V
Nominal Supply Current 20μA
Max Supply Current 100μA
Throw Configuration SPST
Turn On Delay Time 600 ns
Supply Type Dual
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 450 ns
Max Dual Supply Voltage 18V
On-State Resistance (Max) 175Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 1μs, 500ns
Charge Injection 20pC
Switching BREAK-BEFORE-MAKE
Normal Position NO
Voltage - Supply, Dual (V±) ±4.5V~18V
Radiation Hardening No
RoHS Status Non-RoHS Compliant

MAX332CPE Overview


Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around 0°C~70°C TA. The total number of terminations is 16. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Circuits based on SPST - NO switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. Search with MAX332 if you are looking for analog multiplexer variants. It has an internal resistance of 175Ohm. For details about the functions of 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 20V to the switch device in normal circumstances. An effective Dual supply digital multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. If put voltage greater than 100μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic.

MAX332CPE Features


Switch Circuit: SPST - NO

MAX332CPE Applications


There are a lot of Maxim Integrated MAX332CPE Analog Switches & Multiplexers ICs applications.

  • Cross Connects
  • Audio and video switching
  • PCMCIA cards
  • ATM
  • Private Branch Exchange (PBX)
  • Relay Replacement
  • Communication systems
  • Sample-and-hold systems
  • Communications systems
  • Microwave transmission systems

Write a review

Note: HTML is not translated!
    Bad           Good