MAX333ACAP+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin (Sn) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX333ACAP+T Overview
Shipping overseas is convenient due to the electrical component's packing in 20-SSOP (0.209, 5.30mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 20. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. 20 pins are injected to the electronic part body. A SPDT switching circuit is used for these analog switches. A 4 circuit is present in this switch device. Try searching for the analog switch ic with MAX333 if you are looking for variants. Internally, this switch multiplexer has a resistance of 35Ohm. The functions of 20 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 30V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 10V. The switch device would be able to operate with 1μA current. Put voltage above 50μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. The electronic component can function from 20V.
MAX333ACAP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333ACAP+T Applications
There are a lot of Maxim Integrated MAX333ACAP+T Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Cell phones
- Medical Instrumentation
- Digital Cross-Connects
- Cable Modem
- Battery-powered systems
- High-Voltage
- PDH Multiplexers
- Digital cross connects (DSX-1)
- USB 1.1 signal switching circuits
