MAX333ACPP+
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Max Power Dissipation | 889mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Drain to Source Resistance | 140Ohm |
| Height | 4.45mm |
| Length | 26.54mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX333ACPP+ Overview
The electrical component comes in 20-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Through Hole position. 2:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around 0°C~70°C TA. Total terminations are 20. This electronic part offers high-quality output due to its 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. There are 20 pins injected into the electronic part body. The analog switch ics are built using SPDT switching circuits. Search with MAX333 if you are looking for analog multiplexer variants. Analog switches have 35Ohm internal resistance. Datasheets for 20 pin functions are available upon request. In normalcircumstances, users should not exceed 30V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 10V. The switch device would be able to operate with 1μA current. It may damage the digital multiplexer if the voltage is higher than 50μA. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 4.5V should be attached. Operating voltages range from 20V. Resistivity from Drain to Source is 140Ohm for this electronic part.
MAX333ACPP+ Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 140Ohm
MAX333ACPP+ Applications
There are a lot of Maxim Integrated MAX333ACPP+ Analog Switches & Multiplexers ICs applications.
- Video switching
- Mechanical reed relay replacement
- Precision data acquisition
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Sample hold systems
- Transmit
- Fiber In The Loop (FITL)
- Multiplexers
- Intelligent PBX
- Industrial and process control systems
