MAX333ACUP+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Max Power Dissipation | 559mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Height Seated (Max) | 1.1mm |
| Length | 6.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX333ACUP+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 20 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 20 pins. A SPDT switching circuit is used to build these analog multiplexers. This multiplexer is composed of 4 circuits. Try searching for the analog switch ic with MAX333 if you are looking for variants. Analog switches have 35Ohm internal resistance. The datasheets for the 20 pins explain the functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 10V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 1μA current would be sufficient. A voltage higher than 50μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 20VA dual power supply should have at least 4.5V voltage attached. Operating voltages range from 20V.
MAX333ACUP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333ACUP+T Applications
There are a lot of Maxim Integrated MAX333ACUP+T Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Communications systems
- Communication systems
- Video switching
- Fault Tolerant Systems
- Power routing
- Wireless Local Loop
- USB 1.1 signal switching circuits
- Cross Connects
- Low-Voltage
