MAX333ACWP
| Parameters | |
|---|---|
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 800.987426mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX333 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 2.35mm |
| Length | 13mm |
MAX333ACWP Overview
Presented in 20-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. 20 terminations have been made so far. By its 4 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. 20 pins are injected to the electronic part body. Unlike digital switches, these are based on SPDT switching circuits. Use MAX333 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 35Ohm. Datasheets for 20 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. 10V should be the lowest voltage fed to the electronic component. For this digital switch to work, 1μA current would suffice. Put voltage above 50μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There is a voltage range of 20V operating voltages for the electrical part.
MAX333ACWP Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333ACWP Applications
There are a lot of Maxim Integrated MAX333ACWP Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Microprocessor controlled systems
- Remote wireless modules
- Multi-Line E1 Interface Cards
- Cell phones
- Intelligent PBX
- SONET
- 65 V DACs
- High-Voltage
- Imaging
