MAX333ACWP+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| JESD-30 Code | R-PDSO-G20 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Switch-on Time-Max | 175ns |
| Height Seated (Max) | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
MAX333ACWP+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-SOIC (0.295, 7.50mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around 0°C~70°C TA is the extended operating temperature. A total of 20 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 20 series is equipped with this electronic component. A SPDT switching circuit is used for these analog switches. There are 4 circuits in this switch device. Try searching with MAX333 if you're looking for variants.
MAX333ACWP+T Features
1 Channels
Switch Circuit: SPDT
MAX333ACWP+T Applications
There are a lot of Maxim Integrated MAX333ACWP+T Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- SONET/SDH ADM
- Medical systems
- Digital cross connects (DSX-1)
- Imaging
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio and video routing
- Cable PC
- Access Concentrators
- Cable Modem
