MAX333AEAP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX333AEAP Overview
Due to its 20-SSOP (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~85°C TA. In total, there are 20 terminations. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of its design, the 20 series is equipped with this electronic component. On the other hand, analog switches can be constructed using SPDT switching circuits. 4 circuits are used in this analogue multiplexer. Search with MAX333 if you are looking for analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 20 pins functions. Users shouldn't supply more than 30V voltage to the switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 10V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 50μA. There is no problem with using dual supply voltage, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. The electrical part can be operated at 20V voltage levels.
MAX333AEAP Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333AEAP Applications
There are a lot of Maxim Integrated MAX333AEAP Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Communication systems
- ISDN NT1/TA
- 65 V DACs
- FTTH
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- DSLAMs
- USB 1.1 signal switching circuits
- High speed data transmission line cards
- Remote wireless modules
