MAX333AEAP+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | TIN |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX333AEAP+T Overview
Presented in 20-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. A total of 20 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 20 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPDT switching circuits. A total of 4 circuits make up this switch device. Try searching for the analog switch ic with MAX333 if you are looking for variants. This digital multiplexer has 35Ohm internal resistance. Please refer to the datasheets for 20 pins functions. Users shouldn't supply more than 30V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 10V voltage fed to the electrical part below 10V. It would be sufficient to run this analogue multiplexer with 1μA current. Put voltage above 50μA on the multiplexer to cause damage. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 4.5V. This electrical part is compatible with 20V operating voltages.
MAX333AEAP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333AEAP+T Applications
There are a lot of Maxim Integrated MAX333AEAP+T Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Audio and video signal routing
- Battery Powered Systems
- PCMCIA cards
- Multiplexers
- Communication systems
- Avionics
- PBX interfaces
- Fiber In The Loop (FITL)
- Modems
