MAX333AEPP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Max Power Dissipation | 889mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| JESD-30 Code | R-PDIP-T20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 250μA |
| Turn On Delay Time | 145 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Length | 26.16mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX333AEPP+ Overview
As the electronic part is packed in 20-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexer and demultiplexer circuits have a number 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 20. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. An electrical component like this is included in the 20 series. A SPDT switching circuit is used for these analog switches. There are 4 circuits in this switch device. Look for analog switch ic variants by searching with MAX333. Analog switches have 35Ohm internal resistance. For details about the functions of 8 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 10V. For this multiplexer to operate, 1μA current would be sufficient. A digital multiplexer may suffer damage if voltage is applied above 250μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. 20V operating voltages are supported by the electronic component.
MAX333AEPP+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333AEPP+ Applications
There are a lot of Maxim Integrated MAX333AEPP+ Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- USB 1.1 signal switching circuits
- Optical Applications
- Public switching systems
- Residential Gateways, Home Gateway/Router
- Multiplexers
- DVD-R
- Industrial
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Battery Powered Systems
