MAX333AEWP+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -78dB @ 1MHz |
| Height Seated (Max) | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX333AEWP+T Overview
The electrical component comes in 20-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, 20 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. As part of its design, the 20 series is equipped with this electronic component. Based on SPDT switching circuits, these analog multiplexers work. There are 4 circuits in this multiplexer. Try searching for the analog switch ic with MAX333 if you are looking for variants. This digital multiplexer has 35Ohm internal resistance. For details about the functions of 20 pins, please refer to the datasheets. A voltage higher than 30V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. There should be 10V voltage fed to the electrical part below 10V. This multiplexer would work with 1μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 50μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VWhen using dual power supplies, you should attach at least 4.5V. A voltage of 20V can be used to operate the electronic component.
MAX333AEWP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333AEWP+T Applications
There are a lot of Maxim Integrated MAX333AEWP+T Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Video signal routing
- High-Voltage
- Remote wireless modules
- DSUs
- HDTV
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cross Connects
- Channel Banks
- Residential Gateways, Home Gateway/Router
