MAX333CPP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 18V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 130μA |
| Max Supply Current | 130μA |
| Turn On Delay Time | 1 μs |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Drain to Source Resistance | 140Ohm |
| Height | 4.45mm |
| Length | 26.54mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX333CPP+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around 0°C~70°C TA is the extended operating temperature. In total, there are 20 terminations. By its 4 channels, the electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 20 series. Multiplexers built on a SPDT switching circuit are built. Try searching with MAX333 if you're looking for variants. Analog switches have 35Ohm internal resistance. Datasheets for 20 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 30V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. 10V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 1μA current. Put voltage above 130μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. It is recommended that you attach at least 5V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A voltage of 18V can be used to operate the electronic component. This electronic component presents a Drain to Source resistance of 140Ohm.
MAX333CPP+ Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 140Ohm
MAX333CPP+ Applications
There are a lot of Maxim Integrated MAX333CPP+ Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Residential Gateways, Home Gateway/Router
- Multi-Line E1 Interface Cards
- Battery-powered systems
- Communications systems
- Battery Powered Instruments
- Automotive applications
- Microprocessor Controlled Analog Systems
- ISDN NT1/TA
- Audio and video routing
