Parameters |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
5nA |
Channel Capacitance (CS(off), CD(off)) |
5pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
1μs, 500ns |
Crosstalk |
-78dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
1000ns |
Height |
2.35mm |
Length |
13mm |
Width |
7.6mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Number of Pins |
20 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
800mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX333 |
Output |
SEPARATE OUTPUT |
Pin Count |
20 |
Operating Supply Voltage |
18V |
Number of Channels |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
1μA |
Nominal Supply Current |
130μA |
Max Supply Current |
130μA |
Turn On Delay Time |
1 μs |
Voltage - Supply, Single/Dual (±) |
10V~30V ±5V~18V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
500 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
250Ohm |
Min Dual Supply Voltage |
5V |
MAX333CWP+ Overview
Presented in 20-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there have been 20 terminations. A electrical component with 4 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. There are 20 pins injected into the electronic part body. Based on SPDT switching circuits, these analog multiplexers work. MAX333 can be used to search for analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. For details about the functions of 20 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 30V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. It is recommended to use 10V as the lowest voltage for the electrical part. 1μA current would be enough for this multiplexer to operate. A voltage higher than 130μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 18VFor dual power supplies, a voltage of at least 5V should be attached. This analog switch ic utilizes SEPARATE OUTPUT output. It can operate from 18V operating voltages.
MAX333CWP+ Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333CWP+ Applications
There are a lot of Maxim Integrated MAX333CWP+ Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Multi-Line E1 Interface Cards
- Audio signal routing
- Voice over IP/DSL – Integrated Access Devices, Smart
- PBX interfaces
- Automotive applications
- Industrial
- Fiber to the Home
- Cellular phones
- DSUs