MAX333CWP+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Switch-off Time-Max | 500ns |
| Height Seated (Max) | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX333CWP+T Overview
Shipping overseas is convenient with the electronic component packed in 20-SOIC (0.295, 7.50mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around 0°C~70°C TA are extended for operation. Total terminations are 20. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 20 series. A SPDT switching circuit is used to build these analog multiplexers. The multiplexer consists of 4 circuits. If you are looking for variants of the digital switch, trying search with MAX333. Analog switches have 35Ohm internal resistance. To find out what the 20 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 30V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 10V voltage fed to the electrical part below 10V. In order to operate this switch device, it would need a current of 1μA. The analogue multiplexer may be damaged if voltage is greater than 50μA. Despite this switch device's dual supply capability, its voltage should not exceed 18V. It is recommended that you attach at least 5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The electrical part can be operated at 20V voltage levels.
MAX333CWP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333CWP+T Applications
There are a lot of Maxim Integrated MAX333CWP+T Analog Switches & Multiplexers ICs applications.
- SONET
- High-Voltage
- Digital Cross-Connects
- Battery-powered systems
- Cross Connects
- Communication systems
- Fiber In The Loop (FITL)
- Multi-Line E1 Interface Cards
- PBXs
- PDAs
