MAX333EWP+T
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX333 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| JESD-30 Code | R-PDSO-G20 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50μA |
| Max Supply Current | 50μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 250Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 1μs, 500ns |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Switch-off Time-Max | 500ns |
| Height Seated (Max) | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
MAX333EWP+T Overview
This electronic part is conveniently packaged in 20-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, you'll find this switch device. 2:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 20. The electronic part provides high-quality output because it has 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 20 pins is performed into the body of the electrical component. A SPDT switching circuit is used to build these analog multiplexers. It consists of 4 circuits. If you are looking for variants of the digital switch, trying search with MAX333. This digital multiplexer has 35Ohm internal resistance. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 10V. For this digital switch to work, 1μA current would suffice. Put voltage above 50μA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 18V. In the case of dual power supplies, you should connect at least 5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It can operate from 20V operating voltages.
MAX333EWP+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX333EWP+T Applications
There are a lot of Maxim Integrated MAX333EWP+T Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable PC
- Isolation
- Medical systems
- Relay Replacement
- Cable Modem
- ISDN NT1/TA
- Battery-powered systems
- E1 Network Equipment
- E1 Multiplexer
