MAX334MJE/HR
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | ALSO OPERATES WITH 5 TO 15 SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX334 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~15V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 0.9Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 75ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -86dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 50ns |
| Normal Position | NC |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX334MJE/HR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-CDIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. Through Hole is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -55°C~125°C TA. 16 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electrical component is included in the 16 series of products. Based on SPST - NC switching circuits, these analog multiplexers work. There are 4 circuits in this multiplexer. Use MAX334 to search for variants of the digital switches. It has an internal resistance of 50Ohm. Datasheets for 16 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. In order for the electronic part to function properly, the lowest voltage should be 5V. There is no problem with using dual supply voltage, but it should not exceed 15V. If you are using a dual power supply, you should attach at least 5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. This electrical component also includes additional features such as ALSO OPERATES WITH 5 TO 15 SINGLE SUPPLY.
MAX334MJE/HR Features
1 Channels
Switch Circuit: SPST - NC
Additional Features: ALSO OPERATES WITH 5 TO 15 SINGLE SUPPLY
MAX334MJE/HR Applications
There are a lot of Maxim Integrated MAX334MJE/HR Analog Switches & Multiplexers ICs applications.
- Video switching
- E1 Network Equipment
- Signal routing between systems
- Cable Modem
- Microprocessor controlled systems
- Fault Tolerant Systems
- Automotive applications
- Industrial control systems
- High reliability control systems
- Audio and video switching
