MAX335CNG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 24-DIP (0.300, 7.62mm) |
| Number of Pins | 24 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Resistance | 150Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.067W |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 8 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX335 |
| Output | SEPARATE OUTPUT |
| Pin Count | 24 |
| Power Supplies | 5+-15V |
| Number of Channels | 8 |
| Interface | SPI, Serial |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 150μA |
| Max Supply Current | 150μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 150Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 400ns, 400ns |
| Crosstalk | -100dB @ 100kHz |
| Drain to Source Resistance | 150Ohm |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Height | 4.45mm |
| Length | 32.13mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX335CNG+ Overview
Packed in 24-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Around 0°C~70°C TA is the extended operating temperature. The total number of terminations is 24. A electrical component with 8 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. As part of its design, the 24 series is equipped with this electronic component. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with MAX335 if you are looking for variants. As far as internal resistance is concerned, it has 150Ohm. The functions of 24 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 20V. A analog switch ic that has a cost-effective Dual supply type. The lowest voltage fed to the electronic component should be 4.5V. It may damage the digital multiplexer if the voltage is higher than 150μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VYou should attach at least 4.5V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. It has a Drain to Source resistance of 150Ohm ohms.
MAX335CNG+ Features
8 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 150Ohm
MAX335CNG+ Applications
There are a lot of Maxim Integrated MAX335CNG+ Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Industrial control systems
- PBX interfaces
- PBXs
- Multi-Line E1 Interface Cards
- Avionics test equipment
- Frame Relay Equipment
- Optical Applications
- SDH/SONET multiplexers
- Remote Powered Equipment
