MAX335CWG+
| Parameters | |
|---|---|
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 150Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 400ns, 400ns |
| Crosstalk | -100dB @ 100kHz |
| Drain to Source Resistance | 150Ohm |
| Voltage - Supply, Dual (V±) | ±4.5V~20V |
| Height | 2.35mm |
| Length | 15.6mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 150Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 941mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 8 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX335 |
| Output | SEPARATE OUTPUT |
| Pin Count | 24 |
| Power Supplies | 5+-15V |
| Number of Channels | 8 |
| Interface | SPI, Serial |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 150μA |
| Max Supply Current | 150μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Supply Type | Dual |
MAX335CWG+ Overview
As the electronic part is packed in 24-SOIC (0.295, 7.50mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around 0°C~70°C TA. Total terminations are 24. A high-quality output is provided by the electrical component's 8 channels. With a 15V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 24 pins. SPST - NO switching circuits are used in these analog switch ics. Use MAX335 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 150Ohm. Datasheets for 24 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 20V. Analog switch ics with Dual supply type are cost-effective. It is recommended that the electrical component receives a voltage of 4.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 150μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There is 150Ohm resistance between Drain and Source for this electronic part.
MAX335CWG+ Features
8 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 150Ohm
MAX335CWG+ Applications
There are a lot of Maxim Integrated MAX335CWG+ Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- SONET
- Remote wireless modules
- Cellular phones
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channel Banks
- Industrial and process control systems
- Audio and video switching
- Automatic test equipment
- Audio/video switches
