Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
24-SOIC (0.295, 7.50mm Width) |
Number of Pins |
24 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1996 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
24 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
150Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
941mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
8 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX335 |
Output |
SEPARATE OUTPUT |
Pin Count |
24 |
Power Supplies |
5+-15V |
Number of Channels |
8 |
Interface |
SPI, Serial |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
150μA |
Max Supply Current |
150μA |
Throw Configuration |
SPST |
Turn On Delay Time |
400 ns |
Supply Type |
Dual |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
150Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 2pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
400ns, 400ns |
Crosstalk |
-100dB @ 100kHz |
Voltage - Supply, Dual (V±) |
±4.5V~20V |
Height Seated (Max) |
2.65mm |
Length |
15.4mm |
Width |
7.5mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX335EWG+ Overview
Shipping overseas is convenient with the electronic component packed in 24-SOIC (0.295, 7.50mm Width). High reliability is provided by advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. A total of 24 terminations have been recorded. A high-quality output is provided by the electrical component's 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. There are 24 pins injected into the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. Try searching with MAX335 to find analog multiplexer variants. An switch multiplexer with 150Ohm internal resistance has a value of 150Ohm. For functions related to 24 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 20V voltage to the switch device. A cost-effective Dual supply type analogue multiplexer. 4.5V is the lowest voltage that should be fed to the electronic electronic part. Putting voltage greater than 150μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VWhen using dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX335EWG+ Features
8 Channels
Switch Circuit: SPST - NO
MAX335EWG+ Applications
There are a lot of Maxim Integrated MAX335EWG+ Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Digital Cross-Connects
- Sample-and-hold systems
- Relay replacements
- Industrial
- Access Concentrators
- Digital cross connects (DSX-1)
- Automotive applications
- Mechanical reed relay replacement
- DSLAMs