Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
28-SSOP (0.209, 5.30mm Width) |
Number of Pins |
28 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2014 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
700Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
762mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX337 |
Pin Count |
28 |
Operating Supply Voltage |
28V |
Number of Channels |
8 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
1μA |
Propagation Delay |
500 ns |
Turn On Delay Time |
600 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
4.5V~20V ±4.5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
1.11mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
500 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
400Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
82 dB |
Current - Leakage (IS(off)) (Max) |
20pA |
Channel Capacitance (CS(off), CD(off)) |
2pF 20pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Time (Ton, Toff) (Max) |
500ns, 500ns |
Charge Injection |
3.5pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω |
Crosstalk |
-86dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height Seated (Max) |
1.99mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX337CAI+ Overview
Shipping overseas is convenient due to the electrical component's packing in 28-SSOP (0.209, 5.30mm Width). Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 8:1. Operating temperature extended to 0°C~70°C TA. Totally, there are 28 terminations. Due to its 8 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 28 pins. 2 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX337. In this multiplexer, the internal resistance is 700Ohm. The functions of 28 pins can be found in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. 4.5V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. 28V operating voltages can be used with this electrical part.
MAX337CAI+ Features
8 Channels
1μA Supply Current
MAX337CAI+ Applications
There are a lot of Maxim Integrated MAX337CAI+ Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Public switching systems
- Digital access cross connects
- DSUs
- Avionics
- Automatic test equipment
- Audio and video routing
- Audio and video signal routing
- Remote wireless modules