MAX337CWI+T

500ns, 500ns 400Ohm Analog Switches BREAK-BEFORE-MAKE MAX337 28 Pins 20pA 15V 28-SOIC (0.295, 7.50mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX337CWI+T
Package: 28-SOIC (0.295, 7.50mm Width)
Datasheet: PDF
Stock: 327
Description: 500ns, 500ns 400Ohm Analog Switches BREAK-BEFORE-MAKE MAX337 28 Pins 20pA 15V 28-SOIC (0.295, 7.50mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	28-SOIC (0.295, 7.50mm Width)
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2014
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	28
ECCN Code	EAR99
Resistance	400Ohm
Terminal Finish	Matte Tin (Sn)
Max Power Dissipation	1W
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX337
Pin Count	28
Operating Supply Voltage	28V
Number of Channels	8
Number of Circuits	2
Max Supply Voltage	30V
Min Supply Voltage	4.5V
Operating Supply Current	1μA
Propagation Delay	500 ns
Turn On Delay Time	600 ns
Logic Function	Multiplexer
Voltage - Supply, Single/Dual (±)	4.5V~20V ±4.5V~20V
Supply Type	Dual, Single
Supply Current-Max (Isup)	1.11mA
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	500 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	400Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	8:1
Off-state Isolation-Nom	82 dB
Current - Leakage (IS(off)) (Max)	20pA
Channel Capacitance (CS(off), CD(off))	2pF 20pF
On-state Resistance Match-Nom	5Ohm
Switch Time (Ton, Toff) (Max)	500ns, 500ns
Charge Injection	3.5pC
Channel-to-Channel Matching (ΔRon)	5 Ω
Crosstalk	-86dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Signal Current-Max	0.03A
Length	17.9mm
Width	7.5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX337CWI+T Overview

The electronic component is convenient to ship overseas because it is packed in a 28-SOIC (0.295, 7.50mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operation at a temperature around 0°C~70°C TA. 28 terminations have been made so far. This electronic part offers high-quality output due to its 8 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is part of the design of the 28 series that this electronic component is included. The multiplexer consists of 2 circuits. Using the MAX337 search parameter, you can discover variants of the switch. There is 400Ohm internal resistance in this digital multiplexer. normally, users should not supply switches with voltages higher than 30V. An effective Dual, Single supply digital multiplexer. A low voltage of 4.5V should be applied to the electronic component. An operating current of 1μA would be sufficient for this switch device. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. It can operate from 28V operating voltages.