MAX338CPE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX338 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 20pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 11pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 500ns, 500ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX338CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. 8:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around 0°C~70°C TA. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 8 channels. A 15V voltage supply should turn on and run the electronic component. An injection of 16 pins is performed into the body of the electrical component. This multiplexer is composed of 1 circuits. Try searching for MAX338 variants of the analog switch ic. As far as internal resistance is concerned, it has 400Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users should never supply a voltage higher than 30V to a switch device. Dual, Single supply type digital switch with a low cost. There should be 4.5V voltage fed to the electrical part below 4.5V. An operating current of 1μA would be sufficient for this switch device. Despite this switch's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. Operating voltages of 28V are compatible with the electrical part.
MAX338CPE Features
8 Channels
1μA Supply Current
MAX338CPE Applications
There are a lot of Maxim Integrated MAX338CPE Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- New designs requiring multiplexer functions
- Medical Instrumentation
- Residential Gateways, Home Gateway/Router
- Fault Tolerant Systems
- Audio signal routing
- Optical Applications
- Automatic test equipment
- Industrial
- PDH Multiplexers
