MAX338CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX338 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 20pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 11pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 500ns, 500ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX338CSE+T Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 8:1. Around 0°C~70°C TA is the extended operating temperature. Totally, there are 16 terminations. As a result of its 8 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. The multiplexer consists of 1 circuits. Look for analog switch ic variants by searching with MAX338. An switch multiplexer with 400Ohm internal resistance has a value of 400Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexers should not be powered above 30V in normal situations. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 4.5V. This multiplexer would work with 1μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 4.5V voltage attached. A voltage of 28V can be used to operate the electronic component.
MAX338CSE+T Features
8 Channels
1μA Supply Current
MAX338CSE+T Applications
There are a lot of Maxim Integrated MAX338CSE+T Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- E1 Network Equipment
- Industrial control systems
- Mechanical reed relay replacement
- Audio signal routing
- Fiber to the Home
- Intelligent PBX
- High reliability control systems
- Remote wireless modules
- Cross Connects
