MAX339CEE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | TIN |
| Max Power Dissipation | 666.7mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX339 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 500μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 20pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 6pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 500ns, 500ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switch-on Time-Max | 750ns |
| Switch-off Time-Max | 750ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.89mm |
| Width | 3.89mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX339CEE+T Overview
As the electronic part is packed in 16-SSOP (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 4:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. In total, 16 terminations have occurred. As a result of its 4 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Circuits based on SP4T switching are used to construct these analog switch ics. This multiplexer is composed of 2 circuits. Try searching with MAX339 if you're looking for variants. There is 400Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. 4.5V is the lowest voltage the electrical component should receive. An operating current of 500μA would be sufficient for this switch device. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. The electronic component can function from 28V.
MAX339CEE+T Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
MAX339CEE+T Applications
There are a lot of Maxim Integrated MAX339CEE+T Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Communications systems
- T1/E1 Terminals
- MP3 players
- Battery-powered systems
- Optical Applications
- Wireless Local Loop
- Cross Connects
- Cable Modem
- Precision data acquisition
