MAX339CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX339 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 20pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 6pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 500ns, 500ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX339CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, this analog switch is mounted. There is 4:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 4 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. 2 circuits are used in this analogue multiplexer. MAX339 can be used to search for analog multiplexer variants. It has an internal resistance of 400Ohm. Please refer to the datasheets for 16 pins functions. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 4.5V voltage fed to the electrical part below 4.5V. The switch device would be able to operate with 1μA current. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. The electrical part can be operated at 28V voltage levels.
MAX339CPE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX339CPE Applications
There are a lot of Maxim Integrated MAX339CPE Analog Switches & Multiplexers ICs applications.
- Avionics
- Precision data acquisition
- Ultrasound
- Cable Modem
- High-Voltage
- Digital Cross-Connects
- E1 Network Equipment
- HDTV
- Multi-Line E1 Interface Cards
- Medical
