MAX339ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX339 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 4.5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 500μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 20pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 6pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 500ns, 500ns |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX339ESE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. 4:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 4 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SP4T switching circuit is used to build these analog multiplexers. Circuits number 2 make up this analogue multiplexer. Use MAX339 to search for variants of the digital switches. An switch multiplexer with 400Ohm internal resistance has a value of 400Ohm. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 30V voltage to the switch device. 4.5V is the lowest voltage the electrical component should receive. 500μA current would be enough for this multiplexer to operate. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. When using dual power supplies, you should attach at least 4.5V. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. This electrical part is compatible with 28V operating voltages.
MAX339ESE+T Features
4 Channels
Switch Circuit: SP4T
500μA Supply Current
MAX339ESE+T Applications
There are a lot of Maxim Integrated MAX339ESE+T Analog Switches & Multiplexers ICs applications.
- Communication systems
- Communications systems
- Industrial and process control systems
- Video signal routing
- Intelligent PBX
- CSU
- Precision instrumentation
- Medical
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital access cross connects
