Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-WQFN Exposed Pad |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
400Ohm |
Terminal Finish |
Tin (Sn) |
Max Power Dissipation |
1.702W |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.8mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX339 |
Pin Count |
16 |
Operating Supply Voltage |
28V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
1μA |
Propagation Delay |
500 ns |
Turn On Delay Time |
500 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
4.5V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.6mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
500 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
400Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
20pA |
Channel Capacitance (CS(off), CD(off)) |
3pF 6pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
500ns, 500ns |
Charge Injection |
1.5pC |
Channel-to-Channel Matching (ΔRon) |
4 Ω |
Crosstalk |
-92dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Height Seated (Max) |
0.8mm |
Length |
5mm |
Width |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX339ETE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WQFN Exposed Pad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 4:1. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SP4T switching circuits. The multiplexer consists of 2 circuits. Search with MAX339 if you are looking for analog multiplexer variants. It has an internal resistance of 400Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users should never supply a voltage higher than 30V to a switch device. A analog switch ic that has a cost-effective Dual, Single supply type. 4.5V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1μA current would suffice. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. Operating voltages range from 28V.
MAX339ETE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX339ETE+T Applications
There are a lot of Maxim Integrated MAX339ETE+T Analog Switches & Multiplexers ICs applications.
- Central office
- RGB switches
- Sample-and-hold systems
- PBXs
- Medical systems
- Fiber to the Home
- Data Acquisition Systems
- Imaging
- Communications systems
- SONET/SDH ADM