MAX3430ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3430 |
| Pin Count | 8 |
| Operating Supply Voltage | 3.3V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 3.5mA |
| Data Rate | 250kbps |
| Supply Type | Single |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 25mV |
| Number of Transceivers | 1 |
| Simplex/Duplex | Half Duplex |
| Max Junction Temperature (Tj) | 150°C |
| Height | 1.75mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3430ESA+T Overview
Designed for common LEDs, this driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package.In the Tape & Reel (TR) package, this receiver is mounted.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.On any Surface Mount-type PCB or development board, you can install this wide receiver.This differential driver uses 3V~3.6V for power supply.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.IC receiver has been designed primarily for applications operating at -40°C~85°C.An output voltage range of 3.3V is sufficient to run this line driver ic efficiently.In this wide receiver, 8 terminations are integrated for driving and receiving signals from data.There are 8 pinouts available on this transceiver which are market standard.Since the base part number MAX3430 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.8-pin driver IC with improved power dissipation control.Optical transceiver package size is greatly reduced due to downsizing of the ICs and high-density Surface Mount mounting technologies.In terms of resolution, this ic receiver was capable of providing a 1-bit resolution.Typically, the resolution of this receiver is specified to be 1 bits.There is a voltage supply of 3.3V required in order for this transceiver module to be operated.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.ICs implement a total of 1 transceivers.With an input voltage of 3.5mA, this integrating circuit has the ability to drive LEDs with an output voltage of 3.5mA.
MAX3430ESA+T Features
Tape & Reel (TR) package
8 pin count
8 pins
MAX3430ESA+T Applications
There are a lot of Maxim Integrated MAX3430ESA+T Drivers/Receivers/Transceivers applications.
- 1x/2x Fiber Channel
- Wireless security systems
- Routers
- Fiber-to-the-desktop
- Optical sub-assembly (OSA)
- Wireless HD Photography
- Point-to-point networking
- Wireless showroom
- Transmission stations
- LAN, SAN, WAN (local, storage, work area networks)
