MAX3471EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Voltage - Supply | 2.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX3471 |
| Pin Count | 8 |
| Output Type | Adjustable |
| Power Supplies | 3/5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 1.6μA |
| Nominal Supply Current | 100μA |
| Data Rate | 64Kbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 32mV |
| Number of Transceivers | 1 |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 2000 ns |
| Output Low Current-Max | 0.0022A |
| Out Swing-Min | 0.2 V |
| Height | 1.1mm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3471EUA+ Overview
With the enhanced 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package, this driver IC is excellent for driving common LEDs.In this package, the receiver is mounted in the Tube format.Since this part is a Transceiver can transceiver, a number of solutions have been able to utiliTransceivere it for various purposes.PCB or development board with Surface Mount-type connectors can accommodate this wide receiver.It takes 2.5V~5.5V from the power supply to run this differential driver.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.For applications where the operating temperature is -40°C~85°C, this ic receiver was designed primarily.This line driver ic can operate efficiently with a supply voltage range of 3.6V.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.The pinouts for this transceiver are standardized to meet the needs of the market.As the base part number MAX3471 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.It is a 8-pin driver IC with enhanced power dissipation controls.Optical transceiver package size is greatly reduced due to downsizing of the ICs and high-density Surface Mount mounting technologies.It was possible to achieve a 1-bit resolution through this ic receiver.It is typical for this receiver to have a resolution of 1 bits when it is specified.In this category, this rf transceiver module belongs to the Line Driver or Receivers subcategory.This driver IC is designed to operate from a 3/5V power supply.ICs implement a total of 1 transceivers.This integrating circuit is able to drive LEDs with an input voltage of 1.6μA.
MAX3471EUA+ Features
Tube package
8 pin count
8 pins
3/5V power supply
MAX3471EUA+ Applications
There are a lot of Maxim Integrated MAX3471EUA+ Drivers/Receivers/Transceivers applications.
- Clock radio
- Cordless telephone
- Servers
- interconnection between switches
- Structural bonding
- SONET/SDH Network
- Tuner
- WDM transmission
- Aircraft navigation
- LAN, SAN, WAN (local, storage, work area networks)
