MAX3485ESA+T
| Parameters | |
|---|---|
| Output Low Current-Max | 0.0025A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.000002A |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX3485 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3V |
| Supply Current-Max | 2.2mA |
| Data Rate | 10Mbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 50mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 90 ns |
| Transmit Delay-Max | 35 ns |
MAX3485ESA+T Overview
LED drivers with the enhanced 8-SOIC (0.154, 3.90mm Width) package will be able to drive a variety of common LEDs with ease.In the Tape & Reel (TR) package, this receiver is mounted.As a Transceiver can transceiver, this part has enabled many applications to be served.On any Surface Mount-type PCB or development board, you can install this wide receiver.This differential driver consumes 3V~3.6V for its power supplyAt any given time, there can be up to 1/1 eligible receivers/drivers for this electronic part.As its name implies, this ic receiver is designed for applications where -40°C~85°C is the operating temperature.An output voltage range of 3.3V is sufficient to run this line driver ic efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.This transceiver is packaged with 8 market standard pinoutsThe base part number MAX3485 identifies the product type, temperature, package, etc., so you can search for more variants by using it.Using this ic receiver, you were able to achieve a resolution of 1 bits.In the case of this receiver, a resolution of 1 bits is typically specified.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.This driver IC is designed to operate from a 3.3V power supply.Ensure that the VCC pin of the ic receiver receives sufficient but not more than 2.2mA of input current.
MAX3485ESA+T Features
Tape & Reel (TR) package
8 pin count
3.3V power supply
MAX3485ESA+T Applications
There are a lot of Maxim Integrated MAX3485ESA+T Drivers/Receivers/Transceivers applications.
- Shortwave receiver
- Fiber optic cable connection network
- Precision engineering measurement
- Aircraft navigation
- Carrier phase observations
- Cordless telephone
- Switches
- Wireless access points
- Changeing the frequency from IF to RF
- Gigabit Ethernet
