MAX351CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX351 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX351CPE+ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. In Through Hole, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. In total, there have been 16 terminations. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NC switching circuits. There are 4 circuits in this multiplexer. Search with MAX351 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 35Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 30V in normal situations. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 10V. If put voltage greater than 100pA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There is a voltage range of 20V operating voltages for the electrical part.
MAX351CPE+ Features
1 Channels
Switch Circuit: SPST - NC
MAX351CPE+ Applications
There are a lot of Maxim Integrated MAX351CPE+ Analog Switches & Multiplexers ICs applications.
- Routers
- Battery Powered Systems
- DSLAMs
- Industrial control systems
- Avionics and Military Systems
- HDTV
- PDH Multiplexers
- Microwave transmission systems
- Avionics test equipment
- Industrial and process control systems
