MAX351CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX351 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX351CSE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around 0°C~70°C TA. The total number of terminations is 16. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An injection of 16 pins is performed into the body of the electrical component. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching for the analog switch ic with MAX351 if you are looking for variants. In this multiplexer, the internal resistance is 35Ohm. To find out what the 16 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. 10V is the lowest voltage the electrical component should receive. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX351CSE+ Features
4 Channels
Switch Circuit: SPST - NC
MAX351CSE+ Applications
There are a lot of Maxim Integrated MAX351CSE+ Analog Switches & Multiplexers ICs applications.
- SDH
- Multiplexers
- Central office
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Sample-and-hold systems
- PBXs
- Microprocessor Controlled Analog Systems
- Digital access cross connects
- USB 1.1 signal switching circuits
